Jo, taky mám zkušenost "běží to a nestaram se o ně". Co se týká openwrt, tak kdysi jsem se po tom též sháněl, ale nenašel jsem nic. A pochybuji, že se s touhle krabičkou někdo později zabýval. Ale kdyby jste někdo něco našel, tak sem dejte link. Může to být "zajímavé".
__________________
Správce AP zvahov, AS64525 a domény pjih.czf
Óm guru díp namahá.
Dá se u TEW510 nastavit, aby v 5GHz pásmu skákal jen po outdoor frekvencích? Zatím tam mám nastaveno 5580 MHz natvrdo, neboť to konfigurace umožňuje, ale košér to asi nebude, jak jsme se nedávno bavili v diskusi o výkonu.
PS: když se TEW510 nedá kloudně použít jako klient na 5GHz, lze ho nakonfigurovat, aby šel legálně použít v outdoor pásmu jako AP pro 5GHz klienty?
mám na výběr:
Available Countries:
DB - DEBUG
BE - BELGIUM
DK - DENMARK
EE - ESTONIA
FI - FINLAND
DE - GERMANY
GR - GREECE
IS - ICELAND
IE - IRELAND
IT - ITALY
LV - LATVIA
LT - LITHUANIA
LU - LUXEMBOURG
MT - MALTA
NL - NETHERLANDS
NO - NORWAY
PL - POLAND
PT - PORTUGAL
SK - SLOVAK REPUBLIC
SI - SLOVENIA
ZA - SOUTH AFRICA
ES - SPAIN
SE - SWEDEN
GB - UNITED KINGDOM
dal jsem SK, doufám, že slováci to budou mít podobné, jenže jak tomu krámu vysvětlit, že chci používat outdoor, jenco jsem zapnul auto DFS už si skočil na CH60 (5300MHz).
Mám nastavené "RadarDetect Mode: Enabled", tak by si to snad mohlo najít frekvence radarů samo, nebo na to nemá spoléhat? (přece jen vidět a být viděn jsou 2 věci)
Ok, podle výpisu z hlepu:
List of Access Point CLI commands:
add remoteWbr -- Add a remote Wireless Bridge
config wlan -- config wlanX
connect bss -- connect to bssX
del acl -- Delete Access Control List
del key -- Delete Encryption key
del remoteWbr -- Delete a remote Wireless Bridge
find bss -- Find BSS
find channel -- Find Available Channel
find all -- Find All BSS
ftp -- Software update via FTP
get acl -- Display Access Control List
get aging -- Display Aging Interval
get antenna -- Display Antenna Diversity
get association -- Display Association Table
get authentication -- Display Authentication Type
get autochannelselect -- Display Auto Channel Select
get beaconinterval -- Display Beacon Interval
get burstSeqThreshold -- Display Max Number of frames in a Burst
get burstTime -- Display Burst Time
get channel -- Display Radio Channel
get cipher -- Display Encryption cipher
get config -- Display Current AP Configuration
get countrycode -- Display Country Code
get radarnewchannel -- Display radar new channel
get csabeaconcount -- Display CSA Beacon Count
get domainsuffix -- Display Domain Name Server suffix
get dtim -- Display Data Beacon Rate (DTIM)
get encryption -- Display Encryption Mode
get fragmentthreshold -- Display Fragment Threshold
get frequency -- Display Radio Frequency (MHz)
get gateway -- Display Gateway IP Address
get groupkeyupdate -- Display Group Key Update Interval (in Seconds)
get hardware -- Display Hardware Revisions
get hostipaddr -- Display Host IP Address
get ipaddr -- Display IP Address
get ipmask -- Display IP Subnet Mask
get jsw -- Display Jumpstart Mode
get jsP2PassPhrase -- Display JS-P2 passphrase
get key -- Display Encryption Key
get keyentrymethod -- Display Encyrption Key Entry Method
get keysource -- Display Source Of Encryption Keys
get layer2isolate -- Display Layer 2 Isolation Mode
get radardetect -- Display Layer 2 Isolation Mode
get login -- Display Login User Name
get minimumrate -- Display Minimum Rate
get nameaddr -- Display IP address of name server
get operationMode -- Display Operation Mode
get pktLogEnable -- Display Packet Logging Mode
get power -- Display Transmit Power Setting
get radiusname -- Display RADIUS server name or IP address
get radiusport -- Display RADIUS port number
get rate -- Display Data Rate
get reg -- Display the register contents at the given offset
get remoteAp -- Display Remote Ap's Mac Address
get remoteWbr -- Display configured Remote Wireless bridges
get rtsthreshold -- Display RTS/CTS Threshold
get sntpserver -- Display SNTP/NTP Server IP Address
get ssid -- Display Service Set ID
get ssidsuppress -- Display SSID Suppress Mode
get station -- Display Station Status
get SuperG -- Display SuperG Feature Status
get systemname -- Display Access Point System Name
get telnet -- Display Telnet Mode
get timeout -- Display Telnet Timeout
get upsd -- Display UPSD Mode
get uptime -- Display UpTime
get vlan -- Display VLAN Mode
get wirelessmode -- Display Wireless LAN Mode
get wmm -- Display WMM Mode
get wmmParamBss -- Display WMM parameters used by STA in this BSS
get wmmParam -- Display WMM parameters used by this AP
get wlanstate -- Display wlan state
help -- Display CLI Command List
ping -- Ping
pktLog -- Packet Log
reboot -- Reboot Access Point
run -- Run command file
quit -- Logoff
set acl -- Set Access Control List
set aging -- Set Aging Interval
set antenna -- Set Antenna
set authentication -- Set Authentication Type
set autochannelselect -- Set Auto Channel Selection
set beaconinterval -- Modify Beacon Interval
set burstSeqThreshold -- Set Max Number of frames in a Burst
set burstTime -- Set Burst Time
set channel -- Set Radio Channel
set cipher -- Set Cipher
set countrycode -- Set Country Code
set radarnewchannel -- Set radar new channel
set csabeaconcount -- Set CSA Beacon Count
set domainsuffix -- Set Domain Name Server Suffix
set dtim -- Set Data Beacon Rate (DTIM)
set encryption -- Set Encryption Mode
set factorydefault -- Restore to Default Factory Settings
set fragmentthreshold -- Set Fragment Threshold
set frequency -- Set Radio Frequency (MHz)
set gateway -- Set Gateway IP Address
set groupkeyupdate -- Set Group Key Update Interval (in Seconds)
set hostipaddr -- Set Host IP address
set ipaddr -- Set IP Address
set ipmask -- Set IP Subnet Mask
set jsw -- Set Jumpstart Mode
set jsp2Passwd -- Set JS-P2 password
set key -- Set Encryption Key
set keyentrymethod -- Select Encryption Key Entry Method
set keysource -- Select Source Of Encryption Keys
set layer2isolate -- Set Layer 2 Isolation Mode
set radardetect -- Set RadarDetect Mode
set login -- Modify Login User Name
set minimumrate -- Set Minimum Rate
set nameaddress -- Set Name Server IP address
set operationMode -- Set operation Mode
set password -- Modify Password
set passphrase -- Modify Passphrase
set pktLogEnable -- Enable Packet Logging
set power -- Set Transmit Power
set radiusname -- Set RADIUS name or IP address
set radiusport -- Set RADIUS port number
set radiussecret -- Set RADIUS shared secret
set rate -- Set Data Rate
set reg -- Set Register Value
set remoteAP -- Set Remote AP's Mac Address
set rtsthreshold -- Set RTS/CTS Threshold
set sntpserver -- Set SNTP/NTP Server IP Address
set ssid -- Set Service Set ID
set ssidsuppress -- Set SSID Suppress Mode
set SuperG -- Super G Features
set systemname -- Set Access Point System Name
set telnet -- Set Telnet Mode
set timeout -- Set Telnet Timeout
set tzone -- Set Time Zone Setting
set upsd -- Set UPSD Mode
set vlan -- Set VLAN Mode
set wlanstate -- Set wlan state
set wirelessmode -- Set Wireless LAN Mode
set wmm -- Set WMM Mode
set wmmParamBss -- Set WMM parameters used by STAs in this BSS
set wmmParam -- Set WMM parameters used by this AP
timeofday -- Display Current Time of Day
version -- Software version
se frekvence, které se mají vynechat, zadají pomocí set radarnewchannel a výpis get radarnewchannel je to tak?
PS: co kdybych zadal frekvence všech ostatních kanálů krom outdoor (bez radaru) ? Ale zas aby se to vešlo do paměti.
10.10.2008 v 09:41
