R00t.cz DWL-900AP firmware: Porovnání verzí
Z CZFree Wiki
(→Externí odkazy) |
m |
||
| (Nejsou zobrazeny 3 mezilehlé verze od stejného uživatele.) | |||
| Řádek 1: | Řádek 1: | ||
==Vlastnosti== | ==Vlastnosti== | ||
| − | == | + | ==Readme== |
| − | + | ||
| + | <code> ______________________ | ||
R00T'S FW MOD v0.1.1 | R00T'S FW MOD v0.1.1 | ||
| Řádek 10: | Řádek 11: | ||
v0.1.1 [ PRIVATE BETA VERSION ] | v0.1.1 [ PRIVATE BETA VERSION ] | ||
| − | + | ||
+ Speed choices limited again due to errors. Now supports: | + Speed choices limited again due to errors. Now supports: | ||
1,1-2, 1-2-5.5, 1-2-5.5-11, 1-2-5.5-11-22 | 1,1-2, 1-2-5.5, 1-2-5.5-11, 1-2-5.5-11-22 | ||
| Řádek 21: | Řádek 22: | ||
v0.1.0 [ PRIVATE BETA VERSION ] | v0.1.0 [ PRIVATE BETA VERSION ] | ||
| − | + | + Changed power settings to more power choices (0dDm-18dBm) | |
| − | |||
+ Fixed antenna switching (External antenna is external ant. :) | + Fixed antenna switching (External antenna is external ant. :) | ||
+ Added signal graph (you need flash 6 to view it - it's under | + Added signal graph (you need flash 6 to view it - it's under | ||
| Řádek 37: | Řádek 37: | ||
Signal graph description | Signal graph description | ||
| − | + | There are two thick lines in graph: | |
| − | |||
GREEN = signal level | GREEN = signal level | ||
RED = noise level | RED = noise level | ||
| Řádek 48: | Řádek 47: | ||
If there are stronger signal on same channel, you | If there are stronger signal on same channel, you | ||
will get this signal level instead. | will get this signal level instead. | ||
| − | + | </code> | |
==Externí odkazy== | ==Externí odkazy== | ||
| − | *[http://www.r00t.cz/tmp/r00t-3.07-0.1.1.bin | + | *[http://www.r00t.cz/tmp/r00t-3.07-0.1.1.bin Oficiální mirror] |
| − | *[http://www.ok1mjo.com/all/ostatni/Dlink/DWL900APplus/r00t/0_1_1/ | + | *[http://www.ok1mjo.com/all/ostatni/Dlink/DWL900APplus/r00t/0_1_1/ Mirror u -=RYS=-] |
Aktuální verze z 30. 3. 2007, 20:53
Vlastnosti
Readme
______________________
R00T'S FW MOD v0.1.1 ______________________
Change history:
v0.1.1 [ PRIVATE BETA VERSION ]
+ Speed choices limited again due to errors. Now supports:
1,1-2, 1-2-5.5, 1-2-5.5-11, 1-2-5.5-11-22
+ When speed >=5.5 and SHORT preable is selected, PBCC is used
(In AP/Client mode only if all stations can handle it)
+ Anti-Dupe packet filter at RX side - works in CLIENT/P2P BRIDGE
It don't send same packet again on ETH interface. When running
this FW on both sides of P2P link, you will get no longer get
duplicate packets.
v0.1.0 [ PRIVATE BETA VERSION ]
+ Changed power settings to more power choices (0dDm-18dBm)
+ Fixed antenna switching (External antenna is external ant. :)
+ Added signal graph (you need flash 6 to view it - it's under
extras tab.
+ Advanced speed choices: You can select what speeds are set
in beacon frames and what speed is used for data.
NOTE: Beacons are transmitted on LOWEST checked basic rate
Control frames are ALWAYS transmitted at 2Mbps
Data frames are transmitted on checked TX rate or
lower rate (set by client)
Signal graph description There are two thick lines in graph: GREEN = signal level RED = noise level This is average level per 1 second. Around these lines, there are red/green area: This is min / max value interval.
Note: In client mode not only signal for you is measured.
If there are stronger signal on same channel, you
will get this signal level instead.
