Seriová konzole WRT-311

Na této stránce se objevila následující informace:

WRT-311 změna MAC - rozchození konzole

od Jiří Staněk v 10 kvě 2007 00:40

Zdravím,

Laboruji tady zrovna s WRT-311, pokud by se někomu hodila konzole pro zotavení tak tady je návod:

Připojení: sys konektor s označením J4 Při pohledu od portu: 1 - VCC (3,2V) 2 - TX 3 - RX 4 - GND

nastavení terminálu:

Rychlost 38400 8 bit žádná parita 1 stop bit Xon/Soft

A hurá na to!

Po připojení vypíše asi něco takového:

UART1 output test ok Uart init mfid=000000c2 devid=00002249 Found 1 x 2M flash memory

---RealTek(RTL8186)at 2005.09.14-18:49+0800 version 1.3b [32bit](180MHz) no sys signature at 00010000! Jump to image start=0x80300000... decompressing kernel: Uncompressing Linux... done, booting the kernel. done decompressing kernel. early printk enabled Determined physical RAM map: memory: 01000000 @ 00000000 (usable) On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock1 console=0 single Calibrating delay loop... 178.99 BogoMIPS Memory: 14252k/16384k available (1604k kernel code, 2132k reserved, 128k data, 4 8k init, 0k highmem) Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes) Inode-cache hash table entries: 1024 (order: 1, 8192 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) check_wait... unavailable. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Serial driver version 6.02 (2003-03-12) with no serial options enabled ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1 state->flags=00000000 Realtek GPIO Driver for Flash Reload Default block: 64 slots per queue, batch=16 PPP generic driver version 2.4.1 PPP MPPE Compression module registered RealTek E-Flash System Driver. (C) 2002 RealTek Corp. Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000 Creating 2 MTD partitions on "DiskOnChip Millennium": 0x00000000-0x00100000 : "boot+cfg+linux" 0x00100000-0x00200000 : "root fs" RTL8185 driver version 1.9 (2006-03-16) 8186NIC Ethernet driver v0.0.5 (Mar 3, 2006) eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4 eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack PPTP netfilter connection tracking: registered PPTP netfilter NAT helper: registered ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 48k freed mount /proc file system ok! mount /var file system ok! init started: BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) multi-call binary

BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands.

Setting opmode Killing tasks then interfaces Setting MACs Setup bridge(s) device eth0 entered promiscuous mode eth0:phy is 8305 device wlan0 entered promiscuous mode device eth1 entered promiscuous mode eth1:phy is 8305 br0: port 2(wlan0) entering disabled state device wlan0 left promiscuous mode br0: port 3(eth1) entering listening state br0: port 1(eth0) entering listening state br0: port 3(eth1) entering learning state br0: port 3(eth1) entering forwarding state br0: topology change detected, propagating br0: port 1(eth0) entering learning state br0: port 1(eth0) entering forwarding state br0: topology change detected, propagating Setting up IP Starting services Setting Routes Setting up Firewall