Seriová konzole WRT-311

Na této stránce se objevila následující informace:

WRT-311 změna MAC - rozchození konzole

od Jiří Staněk v 10 kvě 2007 00:40

Zdravím,

Laboruji tady zrovna s WRT-311, pokud by se někomu hodila konzole pro zotavení tak tady je návod:

Připojení: sys konektor s označením J4 Při pohledu od portu: 1 - VCC (3,2V) 2 - TX 3 - RX 4 - GND

nastavení terminálu:

Rychlost 38400 8 bit žádná parita 1 stop bit Xon/Soft

A hurá na to!

Po připojení vypíše asi něco takového:

   UART1 output test ok
   Uart init
   mfid=000000c2 devid=00002249
   Found 1 x 2M flash memory
   ---RealTek(RTL8186)at 2005.09.14-18:49+0800 version 1.3b [32bit](180MHz)
   no sys signature at 00010000!
   Jump to image start=0x80300000...
   decompressing kernel:
   Uncompressing Linux... done, booting the kernel.
   done decompressing kernel.
   early printk enabled
   Determined physical RAM map:
   memory: 01000000 @ 00000000 (usable)
   On node 0 totalpages: 4096
   zone(0): 4096 pages.
   zone(1): 0 pages.
   zone(2): 0 pages.
   Kernel command line: root=/dev/mtdblock1 console=0 single
   Calibrating delay loop... 178.99 BogoMIPS
   Memory: 14252k/16384k available (1604k kernel code, 2132k reserved, 128k data, 48k init, 0k highmem)
   Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
   Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
   Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
   Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
   Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
   check_wait... unavailable.
   POSIX conformance testing by UNIFIX
   Linux NET4.0 for Linux 2.4
   Based upon Swansea University Computer Society NET3.039
   Initializing RT netlink socket
   Starting kswapd
   Serial driver version 6.02 (2003-03-12) with no serial options enabled
   ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
   state->flags=00000000
   Realtek GPIO Driver for Flash Reload Default
   block: 64 slots per queue, batch=16
   PPP generic driver version 2.4.1
   PPP MPPE Compression module registered
   RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
   Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
   Creating 2 MTD partitions on "DiskOnChip Millennium":
   0x00000000-0x00100000 : "boot+cfg+linux"
   0x00100000-0x00200000 : "root fs"
   RTL8185 driver version 1.9 (2006-03-16)
   8186NIC Ethernet driver v0.0.5 (Mar 3, 2006)
   eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
   eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
   NET4: Linux TCP/IP 1.0 for NET4.0
   IP Protocols: ICMP, UDP, TCP
   IP: routing cache hash table of 512 buckets, 4Kbytes
   TCP: Hash tables configured (established 1024 bind 2048)
   ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
   PPTP netfilter connection tracking: registered
   PPTP netfilter NAT helper: registered
   ip_tables: (C) 2000-2002 Netfilter core team
   NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
   NET4: Ethernet Bridge 008 for NET4.0
   VFS: Mounted root (squashfs filesystem) readonly.
   Freeing unused kernel memory: 48k freed
   mount /proc file system ok!
   mount /var file system ok!
   init started: BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) multi-call binary

   BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) Built-in shell (msh)
   Enter 'help' for a list of built-in commands.
   Setting opmode
   Killing tasks then interfaces
   Setting MACs
   Setup bridge(s)
   device eth0 entered promiscuous mode
   eth0:phy is 8305
   device wlan0 entered promiscuous mode
   device eth1 entered promiscuous mode
   eth1:phy is 8305
   br0: port 2(wlan0) entering disabled state
   device wlan0 left promiscuous mode
   br0: port 3(eth1) entering listening state
   br0: port 1(eth0) entering listening state
   br0: port 3(eth1) entering learning state
   br0: port 3(eth1) entering forwarding state
   br0: topology change detected, propagating
   br0: port 1(eth0) entering learning state
   br0: port 1(eth0) entering forwarding state
   br0: topology change detected, propagating
   Setting up IP
   Starting services
   Setting Routes
   Setting up Firewall
   #